Sika AnchorFix®-3030
$46.68
Size
Please choose
In stock: 11 available
1
Product Details
Epoxy high performance chemical anchoring adhesive
Sika AnchorFix®-3030 is an epoxy resin based, 2-part, thixotropic, high performance anchoring adhesive for anchoring threaded rods and reinforcing bars in both cracked and un-cracked concrete dry or damp concrete.
- Long open Time
- Sets up in dry, wet or flooded conditions
- High load capacity
Usage
Anchoring adhesive for fixing of non-expanding anchors in the following:
Structural work
- Rebar / steel reinforcement anchoring in new and refurbishment works
- Threaded rods
- Bolts and special fastening / fixing systems
Metalwork, carpentry
- Handrails, balustrades and supports
- Railings
- Window and door frames
Substrates
- Concrete (cracked and un-cracked)
- Hollow and solid masonry
- Wood
- Natural and reconstituted stone
- Solid rock
Suitable for use as a "pick proof" sealant in secure or holding suites and similar facilities (horizontal use only).
Advantages
- Long open Time
- Sets up in dry, wet or flooded conditions
- High load capacity
- Seismic tested (design categories A to F and C1 & C2)
- Suitable for contact with drinking water
- Styrene-free
- Good adhesion to substrate
- Shrinkage-free hardening
- Low emissions
- Low wastage
Packaging
| 385 mL dual cartridge |
12 cartridges per box Pallet: 70 boxes with 840 cartridges |
| 585 mL dual cartridge |
12 cartridges per box Pallet: 44 boxes with 528 cartridges |
Colour
|
Part A |
Off white |
|
Part B |
Grey |
|
A+B mixed |
Light grey |
Mixing Ratio
Part A : Part B = 3 : 1 by volume
Layer Thickness
~8 mm max
Sag Flow
Non-sag, including overhead
Product Temperature
+10 °C min. to +40 °C max. (+50 °F min. to +104 °F max.)
Ambient Air Temperature
+5 °C min. to +40 °C max. (+41 °F min. to +104 °F max.)
Dew Point
Beware of condensation.
Substrate temperature during application must be at least +3 °C above dew point.
Substrate Temperature
+5 °C min. to +40 °C max. (+41 °F min. to +104 °F max.)
Curing Time
|
Temperature |
Open time - Tgel |
Curing time - Tcur |
|
+35 °C to +40 °C |
6 minutes |
2 hours |
|
+30 °C to +35 °C (+86 °F to +95 °F) |
8 minutes |
4 hours |
|
+25 °C to +30 °C (+77 °F to +86 °F) |
12 minutes |
6 hours |
|
+20 °C to +25 °C (+68 °F to +77 °F) |
18 minutes |
8 hours |
|
+15 °C to +20 °C (+59 °F to +68 °F) |
25 minutes |
12 hours |
|
+10 °C to +15 °C (+50 °F to +59 °F) |
40 minutes |
18 hours |
|
+5 °C to +10 °C* (+41 °F to +50 °F) |
150 minutes |
24 hours |
|
+5 °C* (+41 °F) |
300 minutes |
24 hours |
- Minimum cartridge temperature: +10 °C (+50 °F)
MIXING
Preparing the cartridge: 385 & 585 ml
|
|
1.Unscrew the cap |
|
|
2. Remove the cap |
|
|
3. Screw on the static mixer |
|
|
4. Place the cartridge into the application gun ready for use |
When the work is interrupted the static mixer nozzle can remain on the cartridge after the gun pressure has been released. If the resin has hardened in the nozzle when work is resumed, a new nozzle must be attached.
CLEAN UP
Remove uncured material from all tools and application equipment with Sika® Epoxy Cleaner. Cured product can only be removed mechanically.
More Info
Save this product for later
Sika AnchorFix®-3030
Display prices in:CAD